EVRAN 140 Epoxy Repair Compound
FEATURES
EASY MIXING
- One to one by volume or weight
- Colour control mix
- Smooth consistency
GOOD APPLICATION PROPERTIES
- Non-sag properties
- Good spreadability
- Cured coating can be sanded or drilled
- Cured coating is compatible with many paints
EXCELLENT RESISTANCE PROPERTIES
- Non-conductive
- Water resistant
- Resistant to many solvents and chemicals
RECOMMENDED USES
Evran 140 repair compound can be used to repair defects, damage or corrosion pits on a variety of surfaces:
- Most metals
- Fiberglass composites
- Masonry
Evran 140 repair compound can also be used to provide a non-conductive barrier coating for:
- Impressed current anode shields
- Bimetal connections
- Electrical connections
SPECIFICATION DATA — Polyamide Epoxy Putty
| Color | : Gray 140-K-2973 |
| Density (at 20°C) | : dA=1.28 / dB=1.26 / (d mix A+B=1.28 Kg/Lt.) |
| Packaging (Base + Cure) | : 5.00 kg net or 5 Lt. Two-component. 2.5/2.5 Lt (A/B) in metal buckets. |
| Gloss | : Semi-Gloss |
| Flash Point | : >93°C in mixture (Setaflash) |
| Cleaning Thinner | : Navi T-10 |
| Pot Life | : 30–40 minutes at 20°C (for 450 gr mixture). Pot life and drying times depend on temperature and mass. |
| Shelf life | : More than 2 years |
| VOC | : 0 gr/lt. |
| Volume Solids | : 100% |
| Temperature Resistance | : 121°C Dry |
| Theoretical Spreading Rate | : 10 m²/Lt. at 100 mic. DFT |
| Recommended Film Thickness | : 0.5 mm and above. WFT = DFT |
| Application | : Trowel or spreader |
| Maximum humidity in substrate (Masonry) | : 3% |
| Drying Time | : Touch dry: 4 hours. Hard dry: 12 hours. |
Surface Preparation
All metal surfaces must be cleaned to near-white condition equivalent to Steel Structures Painting Council Specification SSPC-SP-10 or Swedish Standard Sa 2½. Other surfaces must be clean, free of oil and dirt, release compounds and other foreign matter.
Mixing
Mix the black base with the white converter (hardener) one to one by volume or weight. Mix the two components until a uniform gray colour is obtained. Do not mix any more material than can be used within 30 minutes.
Application
Apply the mixed components by trowel or other type of spreading tool to the prepared surface. After curing hard, the surface can be sanded.
Precaution
Refer to material safety data sheet of the product. Additional safety information is available upon request. Minimum safety precautions in dealing with the paints are;
- Take precaution to avoid skin and eye contact (i.e. gloves, goggles, face mask, barrier creams, etc.)
- Provide adequate ventilation.
- If the product comes in contact with the skin, wash thoroughly with lukewarm water and soap or suitable industrial cleaner. If the eyes are contaminated flush with water (minimum 10 minutes) and obtain medical attention at once.
- Since these products contain flammable materials, keep away from sparks and open flames. No smoking should be permitted in the area.
- Observe all precautionary notices on containers.
Xn: Harmful for human health. F: Flammable. Warning signs: R11, R20/21/22, R36/38. Safety warnings: S2, S3/7/9, S16, S20/21, S24/25, S38.
Note
To the best of our knowledge, the information contained herein is accurate. However, Navimare-PX assumes no liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of the suitability of any information or material for the use contemplated, the manner of use and whether there is any infringement of patents is the sole responsibility of the user. Additional information may be obtained through your local sales representative or Navimare-PX.
